NCL Tilostik

prod Image
PRODUCT DESCRIPTION

NCL Tilostik is grey cement-based polymer modified, thin bed adhesive for fixing of tiles and stones on levelled walls & floors. It is a high quality factory premixed dry powder with special chemical additives with inorganic fillers. It provides very good bonding strength and full coverage to the tile surface, thereby providing full bed, sound and long lasting installation as compared which results in cavities and poor bonding with conventional mortar. It is suitable for use on most masonry and concrete surfaces. The product is suitable to fix ceramic, vitrified tiles, granite & natural stone both in interior, exterior, external cladding substrates and tile on tile.

prod Image
ADVANTAGES
  • Assured Factory Quality - Eliminates variations in batch mixing at site
  • Eliminates procurement of individual raw materials
  • Single pack system, need to add only water as per recommendation
  • Suitable for interior, exterior and external cladding applications
  • Self-curing product
  • Good tensile adhesion strength
  • Conforms to IS 15477 - Type 2
  • Saves considerable time & labour
  • Good open time
  • Cost-effective
  • No VOC (No toxic fumes)
prod Image
SUITABLE SURFACES
  • Cementitious screeds
  • Cement mortar beds
  • Cement plasters
  • Concrete substrate
prod Image
TECHNICAL DATA
Sl. No. Attributes Standard NCL Block Conforms
1 Appearance Mfg. Spec Dry Powder
2 Color Mfg. Spec White
3 Packing Mfg. Spec 20 kg.
4 Shelf life Mfg. Spec 12 months
5 Mixing proportion with water Mfg. Spec 25 to 30%
5 Mixing proportion with water Mfg. Spec 25 to 30%
6 Pot life Mfg. Spec 180 Minutes
7 Tools Mfg. Spec Notched Trowel& Rubber Trowel
8 Bed thickness Mfg. Spec min 3mm (Depends on tile size)
9 Open time at 25°c Mfg. Spec > 20 Minutes
10 Coverage Mfg. Spec > 3 sft. / kg. for 3mm
11 Time to traffic Mfg. Spec 24 hours
12 Shear adhesion - 14 dry condition > 8 KN / 10 KN > 25 KN
13 Tensile strength -- 14 dry condition 750 N / NA > 1150 N
prod Image
SURFACE PREPARATION

The surface should be dry, clean and free from dust, grease, oil and other contaminates. Keep the following tools ready - mixing tools, trowel, hammer, notched trowel, joint spacers, sponge etc.

Cement based Surfaces: Screeds must be properly cured for 7 days. Cure the concrete for 3 weeks prior to tiling. The surface should be properly levelled for best outcome. Remove curing compounds and any other foreign matter before application which leads to de-bound the Tile Adhesive.

Painted Surfaces: Already paint / lime etc. coated surface should be removed by wire brush or mechanically and loose peeling paint should be removed completely. Allow the surface to dry after cleaning.

prod Image
MIXING

Mix the product with water in the ratio of approximately 1:4 in a clean tub. Take 75% of recommended water and gradually add Tilostik tile adhesive in it. Mixing can be done manually or by mechanical slow speed stirrer. Based on the material consistency adjust the water and mixing to be done, till homogenous lump free mix is obtained. After proper mixing, leave the paste for 5 minutes for polymeric dispersion before application. The paste should be kept away from direct sunlight, heat and use within 180 minutes of preparation (after mixing with water).

prod Image
APPLICATION
  • The backside of tiles is to be cleaned with wet cloth to remove all dust particles Before fixing it.Apply the mixed dough of adhesive on the substrate and spread it by notch trowel. Fix the tiles /stones and press firmly. Then tap properly with rubber hammer in order to spread the adhesive equally and for a good result. Remove any surplus adhesive on the face of the tiles. The tiles adjustment should be done within 15 minutes and before adhesive starts hardening
  • The 3 mm spacing is recommended when fixing the tiles. After 24 hours, NCL􀁈s Cementitious Grouting can be done.
prod Image
PRECAUTIONS
  • Keep out of reach of children
  • Avoid inhalation of dust
  • In case of contact with eyes, rinse eyes with plenty of water and consult a doctor immediately.
Preloader image